The container office is similar to the building. It levels the surrounding area and the base of the partition wall. It is made of reinforced concrete, which is more solid. Then the pillars are connected with the skeleton with transverse beams, and the upper partitions, the outer wall panels and the doors and windows frame are connected; then the floor is laid and the upper floor is installed, then the roof truss and the roof panels are mounted; finally, the doors and windows are installed, and the vertical support is pulled. There are also sanitary ware, hardware and so on. Next, the resident container manufacturer will give us a detailed introduction to the matters needing attention in the process of construction! _________

1.各構件裝置位置應契合設計請求，現場焊接部件位應精確，無假焊、漏焊。緊固件應契合GB5782規則，螺栓必需按設計請求的規則，位置裝置正確并墊好墊圈，不得少裝、漏裝；構件間的銜接螺栓必需要擰緊。

1. The location of each component should meet the design requirements, and the location of field welding components should be precise, without false welding or leakage welding. Fasteners should conform to GB5782 rules. Bolts must be in accordance with the design requirements. Location devices should be correct and gaskets should be padded properly. No less or less filling should be allowed. Connection bolts between components must be tightened.

2.經現場焊接及運輸途中底漆剝落處應重刷防銹漆一層，構件露明部位刷面漆二層，油漆不得有漏刷、脫皮、掛漆及返銹現象。

2. After welding and transportation on site, the primer spalling should be repainted with one layer of anti-rust paint, and the component exposed part should be repainted with two layers of top paint. No leakage, peeling, hanging and rust-back of the paint should be allowed.

3.按排板圖將集裝箱辦公室、墻面塊必需校正，傘墻的轉角處及陽角處用角鋁封口，板與板之間銜接采用工字鋁銜接，各墻須垂直，嵌縫深度分歧，劃一清潔，墻面應清潔，顏色分歧，板縫齊整，打釘面上下要分歧，不得有參差，必要部位采用自攻螺栓。按設計圖紙標明集裝箱會議室門窗位置，用切割機割出門窗洞位置，依照門窗洞位置裝置窗門，窗為塑鋼窗，北京集裝箱活動房租賃停止底層的吊頂。

3. The first piece of container office and wall must be corrected according to the layout. The corner and sunny corner of umbrella wall should be sealed with angle aluminium. The connection between the board and the board should be made of I-shaped aluminium. The walls should be vertical, the depth of insertion should be different, and the wall should be clean, the color should be different, the board seams should be neat, the nailing surface should be divergent, there should be no difference between the top and bottom, and the necessary parts should be self-tapping bolts. According to the design drawings, the position of the door and window of the container meeting room is marked, and the position of the door and window hole is cut out by cutting machine. According to the position of the door and window hole, the window is made of plastic steel window. The suspended ceiling of the bottom floor of the Beijing container moving room is leased.

4.門窗位置裝置正確并用螺栓緊固。裝置開啟靈敏而無阻滯現象，玻璃不應有麻面和裂痕，玻璃干凈，附件裝置結實。

4. The door and window positioning device is correct and bolted. The device opens sensitively without blocking. There should be no pitting and cracks in the glass. The glass is clean and the accessory device is strong.

5.外觀請求：①墻須垂直平整分歧，劃一清潔。②墻面應清潔，顏色分歧，板縫齊整。③門窗鎖開關靈敏，不得缺附件。

5. Appearance Requirements: 1. The walls shall be vertical, flat and divided, and uniformly cleaned. (2) The walls should be clean, with different colours and neat joints. (3) The door and window lock switch is sensitive and can not be without accessories.

以上精彩內容由濟南住人集裝箱整理提供，更多關于住人集裝箱的詳情，歡迎咨詢我們官網的客服人員：http://www.king-seng.com！我們將會盡快給您做出回復！謝謝大家的支持！

The above wonderful contents are provided by Jinan Resident Containers. More details about Resident Containers are welcome to consult our customer service staff on our official website: http://www.king-seng.com! We will reply to you as soon as possible! Thank you for your support!